Chimney Inspection in Winston-Salem, NC | Jasper Chimney Sweep

Chimney Inspection in Winston-Salem - Flat-Price Sweep, Findings in Writing

A flat-price sweep with a camera inspection and photo report included. If we find something that needs attention, you see the picture before you hear a price - and we will tell you when it can wait.

Flat price quoted before we book

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Inspection for Winston-Salem Homeowners

Most chimney problems start quietly. A cracked flue tile, a thin bead of water staining on the ceiling near the chase, a cap that came loose in a spring wind – none of it announces itself, and none of it is visible from the living room. That’s the gap a proper inspection closes. Jasper Chimney Sweep treats your chimney as a system, not just a dirty flue, and our technicians have up to 9 years of experience reading exactly what a Winston-Salem chimney is telling them. We inspect, sweep, and repair under one roof, so nothing falls through the cracks between contractors. Same-day appointments are often possible. Call (866) 343-2983. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Call (866) 343-2983

Fireplace Inspection

Fireplace Inspection is the close look at the firebox, damper, smoke chamber, and the first stretch of flue above the fire – the parts that take the most heat and the parts a flashlight from the hearth can’t reach. You need one when you’ve just bought a house, when smoke rolls out instead of up, when the damper stops seating, or when it’s been more than a season since anyone looked. We open the firebox, check the damper and smoke shelf, look for cracked refractory brick and gaps in the mortar joints, and run a camera up the flue. A fireplace inspection in Winston-Salem typically runs $125-$250 depending on how many flues and how much camera work the fireplace needs. The written estimate sets the final price.

What We Check in the Firebox

We look at the brick face, the refractory panels, the damper blade and its frame, and the smoke shelf above the damper. Hairline cracks in refractory are common and not always serious; deep ones that let heat reach the surrounding framing are a different story. We tell you which is which.

Damper and Smoke Shelf Condition

A damper that won’t close all the way leaks heat up the chimney all winter and lets cold air down when the fire is out. The smoke shelf above it collects soot and creosote that can fall back into the firebox. We check both and clear them as part of the visit.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Inspection Services

Chimney Inspection Services cover the full system: firebox, flue, crown, cap, flashing, and the exterior masonry, checked together rather than one piece at a time. You need them before you burn for the season, after a chimney fire or a storm, when you’re selling a home, or when an insurer asks for documentation of the chimney’s condition. Jasper Chimney Sweep pairs a full-system inspection with every sweep, so you get a written understanding of what your chimney needs rather than a cleaning receipt. A standard inspection in Winston-Salem typically runs $125-$250, and a Level 2 with camera work runs $200-$400. Every price is estimated per job and confirmed in writing before any work begins.

What the Written Report Covers

The report notes each component we checked, what condition it’s in, and whether anything needs attention now or can safely wait. You get the photos and the camera footage, not just our summary. That matters if you ever need to show an insurer or a buyer.

What the Written Report Covers

Working With Your Insurer

When a carrier asks for proof the chimney was inspected or swept, the written report does that job. We can work with your insurer on documentation. If a repair is recommended, the report explains why in plain terms so the recommendation stands on evidence, not on pressure.

Working With Your Insurer
Need help today?Fast, friendly service and a no-obligation free estimate.

Call (866) 343-2983

Chimney Flue Inspection

Chimney Flue Inspection is the examination of the flue itself – the liner, its joints, and the path the smoke and gases actually travel – using a camera where the eye can’t follow. You need one whenever there’s been a fire, a change in how the fireplace burns, creosote buildup past a glaze stage, or a suspected liner problem. We run a camera the length of the flue, check every tile joint and the liner’s connection at top and bottom, and look for gaps, spalling, and offset tiles that let heat and carbon monoxide reach the structure. A flue inspection in Winston-Salem typically runs $150-$300 depending on the flue length and access. HeatShield ceramic sealant, which most generalist services don’t carry, lets us repair a damaged liner from the inside when the flue is otherwise sound.

Reading the Liner From the Inside

A clay tile liner cracks at the joints first, and those cracks are invisible from below. The camera shows them clearly. We record the run so you can see the same thing we did and judge it for yourself.

When a Liner Needs Sealing

If the tiles are sound but the joints have opened, a HeatShield sealant repair can restore the flue’s interior surface without tearing out masonry. If the flue is too far gone for that, we’ll tell you plainly and walk through the relining options.

Chimney Fire

Chimney Fire damage is what you call in when a fire has burned inside the flue – sometimes loudly, sometimes as a low roar you barely noticed – and the liner and surrounding masonry need a full assessment before the fireplace is used again. You need an inspection after any chimney fire even if it seemed small, because the damage that matters is usually behind the tile face. We examine the full flue for cracked or spalled tiles, check the smoke chamber and damper, look at the cap and crown, and confirm the structure around the chimney is sound. Post-fire inspection and any related repair in Winston-Salem typically runs $200-$400 for the inspection; the repair estimate follows in writing. Do not light another fire until the flue has been checked by a trained professional.

What to Do Right After

Get everyone out and call the fire department if there was a live fire in the flue. Once it’s out, don’t burn again until the chimney has been inspected. A fire that stayed inside the flue can still have cracked tiles or warped metal that won’t show until the next burn.

How We Assess the Damage

We run a camera the length of the flue, check the firebox and smoke chamber for heat damage, and inspect the crown and cap for spalling. Creosote left behind after a fire is often glazed and stubborn, so a proper sweep usually comes before any repair.

Level 2 Chimney Inspection

Level 2 Chimney Inspection is the camera-based, full-system inspection the trade uses when a standard look-over isn’t enough – it covers the flue, firebox, and every accessible part of the chimney’s exterior with video documentation. You need one when you’re buying or selling a home, after a chimney fire, after an earthquake or major storm, or when you’ve changed the appliance the chimney serves. We run a camera through the entire flue, inspect the crown, cap, flashing, and masonry from the roofline, and put the whole thing in a written report with photos. A Level 2 inspection in Winston-Salem typically runs $200-$400 depending on the number of flues and roof access. The written estimate sets the final price.

Video Documentation You Keep

The camera footage comes with your report. If a seller tells a buyer the chimney is fine, or an insurer wants proof of condition, the video is what settles the question. We show you what we found rather than describing it.

What Triggers a Level 2

A home sale, a chimney fire, a storm that struck the roof, or a change in the appliance – each means the standard look-over can’t tell the full story. The camera is what closes the gap.

Chimney Leak

Chimney Leak problems start at the top and travel down – a failed crown, a worn flashing seal at the roofline, a missing cap, or masonry that has absorbed water and is letting it through. You need an inspection when you see a damp patch on the ceiling near the chase, water in the firebox, rust on the damper, or crumbling mortar on the chimney’s exterior. We check the crown for cracks, the flashing where the chimney meets the roof, the cap condition, and the masonry for spalling or soft brick, and we trace where the water is actually entering rather than guessing. A leak inspection in Winston-Salem typically runs $150-$300; any repair is quoted separately in writing. We install Gelco and Famco caps and dampers so the fix lasts past the next storm.

Tracing the Actual Entry Point

Water rarely enters where the stain appears. The crown, the flashing, and the cap are the usual suspects in that order. We check each and tell you which one failed, with photos to back it up.

Repairs That Hold Up

A cracked crown gets rebuilt, loose flashing gets resealed, and an open flue gets a proper cap. Cheap caps that need replacing in a season or two aren’t worth the trip, which is why we install Gelco and Famco caps built to last.

Chimney Camera Inspection

Chimney Camera Inspection uses a video camera run the length of the flue to see what no flashlight at the firebox can reach – cracked tiles, gaps at the joints, offset sections, and the true state of the liner. You need one whenever there’s been a fire, a suspected liner failure, a change in how the fireplace burns, or when you want an honest second opinion on work someone else recommended. We record the entire run, narrate what we’re seeing as we go, and give you the footage with a written summary of the flue’s condition. A camera inspection in Winston-Salem typically runs $175-$350 depending on flue length and access. Our DuraFlex flexible liner systems follow where the footage shows a reline is genuinely needed.

What the Camera Reveals

Tile joints that have opened, spalling that hasn’t reached the surface, gaps where the liner meets the flue top. None of it is visible from the hearth. The camera shows the whole run, and you see what we see.

When a Camera Is Essential

After a chimney fire, after a reline, and before you accept a recommendation for thousands of dollars of liner work. If someone says the liner needs replacing, the camera footage should show the reason.

Brands We Service

We install and service DuraFlex flexible liner systems, and we know where a stainless liner wears first – at the top where it meets the cap, and at the bottom connection to the appliance collar. A DuraFlex install depends on the fit, and we size the liner to the flue rather than the flue to the liner. We also work with HeatShield, the ceramic sealant system used for liner repair from the inside, and we apply it only on a flue whose tiles are structurally sound.

We fit Gelco and Famco caps and dampers, which are built for longevity rather than a fast replacement that brings you back next season for the same fix. We also work with Olympia Chimney and Copperfield on the wider range of chimney components those brands cover. Whether you have DuraFlex, HeatShield, Gelco, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Smoke spilling into the room. A fireplace that puffs smoke instead of drawing it means the flue, damper, or smoke chamber has a problem. It can also signal a blocked flue, which is a carbon monoxide concern.
  • A strong creosote smell in warm weather. Creosote that has baked onto the flue lining gives off an odor when the chimney warms up and the fire is out. If it’s severe, the buildup may be glazed and needs a professional sweep before the next burn.
  • Water stains on the ceiling or rust in the firebox. Either one points to a leak from the crown, flashing, or cap. Water soaking into masonry worsens with every rain and can lead to freeze damage and crumbling mortar over time.
  • Visible cracks in the exterior masonry or crown. Cracks in the crown and gaps in the mortar let water in and can widen with seasonal freeze and thaw. A professional look tells you which cracks matter and which can wait.
  • A chimney fire you noticed, however small. Even a quiet chimney fire can crack tiles and leave glazed creosote behind. Don’t light another fire until a trained professional has inspected the flue.

Our Process, Step by Step

  1. 1
    We talk through what you’ve noticed. Before we climb anything, we ask about the fireplace, how often you burn, any smoke or water issues, and whether an insurer or buyer prompted the visit. That shapes where we focus.
  2. 2
    We protect the work area and set up the camera. Drop cloths go down, and the camera goes up the flue. The whole run is recorded so you end up with the same footage we do – not a verbal summary of something you can’t verify.
  3. 3
    We inspect the full system. Firebox, damper, smoke chamber, flue, crown, cap, flashing, and exterior masonry, checked together rather than one piece at a time. We photograph anything we find.
  4. 4
    We sweep the flue when it needs it. If creosote has built up, we sweep before we finish the inspection so the camera view isn’t obscured. The sweep is the same visit, not a separate appointment.
  5. 5
    We walk you through the findings and the written report. What’s fine, what needs attention now, and what can safely wait. Any repair is quoted in writing, and nothing begins without your go-ahead.

How Much Does Chimney Inspection Cost in Winston-Salem?

A typical basic inspection in Winston-Salem runs $125-$250 depending on the number of flues and whether the chimney serves a fireplace alone or a fireplace plus an appliance. A Level 2 inspection with camera work runs $200-$400, and the price moves with roof access, flue length, and how many flues need documenting. A flue-specific camera inspection runs $175-$350. A fireplace inspection runs $125-$250. Leak and post-fire assessments fall in the $150-$300 range for the inspection, with any repair quoted separately in writing.

What affects the price: the number of flues, the height and pitch of the roof, whether access is easy or cramped, and whether you need a written report for a home sale or an insurer. A single flue on a low roof costs less than a three-flue chimney with a steep pitch, and that’s the honest reason the range exists.

How to avoid overpaying: get the inspection first, and insist on seeing the camera footage before agreeing to any repair. If a recommendation comes without evidence you can see, ask why. Nothing is recommended here without camera evidence you can see for yourself, and we’ll tell you plainly when work can safely wait.

What’s included in a free estimate: the walk-through, the camera footage, the written findings, and a written quote for any repair. The estimate is free and the price is set per job by the written estimate, so there’s no surprise on the invoice. Call (866) 343-2983 for an exact quote.

Our Service Area Near Winston-Salem

We serve homeowners across the Winston-Salem area and the surrounding towns, including Clemmons, Rural Hall, Lewisville, Midway, Tobaccoville, Bermuda Run, King, Welcome, Lexington, Mocksville, and Tyro. Roof access and drive time vary by neighborhood, so we schedule each visit with that in mind. If you’re in Clemmons or Rural Hall, we’re close by. To see the full list of communities we cover, visit our Winston-Salem service page.

Serving Winston-Salem, NC – Our Local Coverage Area

We serve Winston-Salem and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Inspection in Winston-Salem

Schedule Your Chimney Inspection Service in Winston-Salem Today

Know exactly what your chimney needs before any work begins. Inspect, clean, repair – handled by one team, one standard of work, with professional-grade materials the same certified technicians specify. We treat your chimney as a system, not just a dirty flue, and the camera footage is yours to keep. Call (866) 343-2983 for a no-obligation free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Two of our core services, chimney sweep and chimney repair, run alongside every inspection.

Written by the team at Jasper Chimney Sweep.

Why Winston-Salem Chooses Jasper Chimney Sweep

We set the standard for chimney inspection in Winston-Salem.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Winston-Salem

Getting your chimney inspection handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney inspection needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney inspection pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Winston-Salem Customers Say

Trusted by homeowners across Winston-Salem and surrounding areas.

★★★★★

"Fast, fair, done right. No notes."

Farah Saleh
★★★★★

"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."

Lisa Reed
★★★★★

"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."

Mark Rhodes

Ready for Chimney Inspection in Winston-Salem?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Winston-Salem.

(866) 343-2983

Request a Free Estimate in Winston-Salem

Tell us about your chimney inspection needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - We Answer 24/7