Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Winston-Salem Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning and service in Winston-Salem. DuraFlex is a stainless steel flexible relining system, so work on it means understanding liner sizing, insulation wraps, and the top-plate and cap termination, not just brushing out a firebox. Our technicians have up to 9 years of experience with flexible liner systems and the venting geometry common in this city’s older masonry chimneys.
That last point matters more in Winston-Salem than in most places. The city’s sweep market is dominated by a large stock of pre-1950 homes with original masonry fireplaces and flues, many in historic districts like West End and Old Salem where exterior modifications are restricted. Work here has to respect interior dust control and liner approaches that don’t alter historic chimney exteriors. A flexible liner often sits inside a chase that was never built for one, and how it terminates, seals, and handles condensate decides whether it stays clean or turns into a creosote trap.
To be clear about who we are: we are an independent DuraFlex service provider. We’re not affiliated with or authorized by DuraFlex, and we don’t speak for the manufacturer. We inspect, clean, and repair DuraFlex installations using quality parts that fit them. Call (866) 343-2983 to book. We answer 24/7, with fast dispatch from 7am to 7pm.
Why Trust Jasper Chimney Sweep for Your DuraFlex Chimney Cleaning?
DuraFlex components have specific fit and sealing requirements, and our technicians have spent years learning them in the field. That means recognizing when a top plate has been set without a proper storm collar seal, when an insulation wrap is missing from an exterior chase, and when corrugations at an offset are holding soot a brush alone won’t reach. We work with DuraFlex ReliaFlex, ProFlex, and insulated flexible liners with foil-faced wrap, and we match repairs to components specified for that equipment rather than generic hardware-store substitutes.
Warranty-safe practice guides everything we do. We don’t cut, crush, or re-route a liner to make a repair fit, because that’s how a listed system stops being a listed system. When a component needs replacing, we choose parts built for DuraFlex terminations so the assembly keeps its integrity. And because we also work with HeatShield ceramic sealant and Gelco caps, we can address the whole venting path rather than hand off the awkward parts to someone else.
The team that inspects your chimney is the same team that sweeps and repairs it. Nothing falls between contractors, and you get one written picture of what your liner needs before any work begins.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Winston-Salem
Winston-Salem’s humid subtropical climate brings mild winters, damp springs, and the occasional ice storm. That combination is hard on flexible stainless liners, especially in exterior masonry chases. These are the problems we see most often on DuraFlex installations in Winston-Salem.
- Uninsulated liner in an exterior chase. When a flexible liner goes into an exterior masonry chase without insulation, flue gases hit cold stainless walls and creosote condenses heavily. The result is glazed, third-degree creosote that a standard sweep brush slides right over. Removing it takes a chemical treatment and a proper sweep, sometimes more than one pass.
- Top-plate or cap termination without a storm collar seal. A top plate set without a properly sealed storm collar lets rain run down the outside of the liner. That water reaches the appliance connector and rusts it from the outside in. Resealing or replacing the termination is usually the fix, and it’s a common reason a chimney that “looks fine” has a corroded connector.
- Soot trapped in the corrugations. Flexible liner corrugations catch soot at every offset and bend. That hidden buildup doesn’t show up from the firebox and can restrict draft long before it blocks the flue. Only a Level 2 camera inspection reveals it, which is why we pair one with the sweep on any DuraFlex job where draft has changed.
- Liner sized for wood, now serving gas or an insert. A liner sized for a wood appliance that later gets converted to gas or an insert runs cooler than it was chosen for. Cooler flue gases mean condensation, and condensate plus residual creosote turns acidic and attacks the stainless from inside. This is one of the quietest failures a flexible liner develops.
- Fall leaf load on caps and spark arrestors. Winston-Salem’s heavy leaf fall lands right when sweeping season starts. Leaves pack into caps and spark arrestors, and a clogged termination changes how the whole liner vents. Clearing it is simple; catching it before it causes a smoky backdraft is the point of an inspection.
Homeowners with a DuraFlex ReliaFlex liner in an exterior chimney often call because of a smoky smell on damp days or a draft that has gotten worse over a season. A Level 2 camera inspection commonly reveals glazed creosote on the corrugations and a top plate whose storm collar has pulled away from the crown. The usual fix is a chemical creosote treatment followed by a proper sweep, then resealing or replacing the top plate and cap so the liner terminates correctly.
DuraFlex Parts & Our Repair-vs-Replace Approach
Parts choice on a DuraFlex installation comes down to fit and sealing. Terminations, adapters, and top plates need components specified for DuraFlex top plates, because generic caps and adapters often don’t seal correctly on them. A cap that sits a quarter inch off true is a water path, and water is what kills flexible liners from the outside.
We don’t claim to stock OEM or genuine DuraFlex parts, and we’re not a DuraFlex dealer. We source quality parts that fit DuraFlex equipment and meet the sealing needs of the assembly.
Our repair-versus-replace call follows one rule: if the liner itself has failed, we’ll price a full reline rather than patch a stainless flue. Patching a compromised flexible liner rarely restores safe venting, and a patch that lets you burn one more season isn’t a repair. If the liner is sound and the problem lives at the termination or in trapped soot, we fix that and tell you plainly when the rest can wait.
If you’re not sure which side of that line your chimney falls on, call (866) 343-2983 for a free estimate.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection and camera run of the flue. On a DuraFlex liner that means checking the insulation wrap, the corrugations at every offset, and the top plate from the roof side as well as the firebox side. You see the camera footage.
- 2
Repair or install. For creosote, a chemical treatment goes on first, then the sweep, so glazed deposits release instead of glazing harder. For termination and cap work, we reseal the storm collar or set a cap that seals properly on the DuraFlex top plate. For a failed liner, we size and install a replacement with the insulation the chase calls for.
- 3
Test. We verify draft and check for water paths at the termination before we call the job done. A cap that looks right and leaks is still a leak.
- 4
Warranty and record. You get a written record of what we did and what we found, including the condition of the liner and termination, with any conditions to watch. That record is what protects a warranty claim down the road, and it’s what a preservation review may ask for in a historic district.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Winston-Salem
We work with the DuraFlex flexible liner systems found in Winston-Salem homes: the ReliaFlex flexible stainless liner, the ProFlex flexible liner kit, and the insulated flexible liner with foil-faced wrap. Service covers cleaning, inspection, termination and cap work, and replacement when a liner has failed.
Because many of Winston-Salem’s early-20th-century Craftsman and Tudor Revival homes have brick masonry fireplaces and clay tile flues that were never lined, a good share of our DuraFlex work is on liners installed to bring an old clay flue up to modern venting standards. In Ardmore and West End, original 1920s clay tile flues often have offset joints and no liner, so sizing the flexible liner to the existing flue matters more than it does in a straight, modern one.
We also see mid-century ranches with factory-built fireplaces where a liner was added later. Those installs often need the same checks on insulation and top-plate sealing.
We Also Service These Brands
DuraFlex is one piece of a larger picture. We also install and service HeatShield ceramic sealant repair for liners that can be sealed rather than replaced, and Gelco caps and dampers for weatherproofing the top of the chimney. Working across brands means we recommend what your chimney needs, not what we happen to sell. If a HeatShield repair serves you better than a reline, we’ll say so.
FAQs – DuraFlex Chimney Cleaning Service in Winston-Salem
Can a DuraFlex liner be cleaned with a standard wire chimney brush? Not on its own, no. A standard wire brush handles light soot, but glazed creosote bonded to stainless corrugations needs a chemical treatment first, then a sweep, or the brush just polishes it. If your liner runs through an exterior chase without insulation, expect glazed deposits to be the norm rather than the exception. Call (866) 343-2983 for a free estimate.
Why does my DuraFlex-equipped chimney smell worse than my neighbor’s? Usually because of the termination or the insulation. A top plate whose storm collar has pulled away lets water down the outside of the liner, and damp creosote smell is the first sign. A liner in an exterior chase without insulation also runs cold and holds more condensate than an interior one. Both are fixable, and a camera inspection shows which one you have. Call (866) 343-2983 for a free estimate.
Does a DuraFlex liner need a Level 1 or Level 2 inspection? A Level 2 inspection is the right call on a flexible liner whenever draft has changed, an appliance has been swapped, or it’s been a while since the last look. Level 2 includes a camera run of the flue, which is the only way to see soot trapped at corrugations and offsets. A Level 1 visual check suits a liner you already know is sound. Call (866) 343-2983 for a free estimate.
Can I put a multi-flue cap on a chimney with one DuraFlex liner and one masonry flue? Yes, provided the cap is set so each flue still terminates correctly and the DuraFlex top plate keeps its own seal. A multi-flue cap that bridges both flues without accounting for the top plate can trap water at the liner termination. We check the seal on both sides before recommending one. Call (866) 343-2983 for a free estimate.
My DuraFlex liner was installed for wood – can I switch to a gas insert without changing it? Not automatically, and it’s worth a real look first. A liner sized for wood runs cooler on gas, and cooler flue gases condense on stainless, which turns residual creosote acidic. Sometimes the existing liner serves fine; sometimes the right call is a change. A camera inspection and sizing check settles it. Call (866) 343-2983 for a free estimate.
How much does DuraFlex chimney cleaning cost in Winston-Salem? Pricing is set per job by the written estimate, and the estimate itself is free. What you’ll pay depends on how much glazed creosote is on the liner, whether the termination needs resealing, and whether a cap replacement is involved. Nothing is recommended without camera evidence you can see for yourself, and we’ll tell you plainly when work can safely wait. Call (866) 343-2983 for an exact quote – estimates are free.
Book Your DuraFlex Service in Winston-Salem, NC
A flexible stainless liner rewards the right maintenance and punishes skipped checks in ways that stay hidden until they’re expensive. Whether your DuraFlex chimney needs a sweep, a creosote treatment, cap work, or an honest assessment of a liner that’s failed, we’ll inspect it, show you what we find, and tell you what it needs. Call (866) 343-2983 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm.
Written by the team at Jasper Chimney Sweep.